All UK Cars, vans & lorries recalls and safety alerts, newest first, with the hazard, affected models and what to do next. 4,358 listed.
Due to improper programming of the airbag system in the Airbag Sensor Assembly (airbag control module) there is a possibility that the Airbag Sensor Assembly may erroneously detect a rollover and deploy the Curtain…
It has been identified that under certain unusual conditions the High Mounted Stop Lamp (HMSL) fitted to Navara accessory hardtops does not illuminate simultaneously with the vehicle's stop lamps. During engine start it is…
It has been identified on certain 6 cylinder diesel engine/9 speed automatic transmission vehicles the starter/alternator/transmission wiring harness may be too close to the exhaust system. If it is then there is a risk…
The brake servo booster may not have been correctly manufactured. This may cause a harder feel to the brake pedal operation and require more effort from the driver.
It has been identified that due to a nonconformity in the transmission casing mount material there is a possibility that the casting may fail. This may affect the control of the vehicle.
It has been identified that during production a small number of Fiesta's may not have had the right-hand side front seatbelt top anchor bolt tightened to the correct specification. This may result in the…
It has been identified that during the engine warm-up process and under certain driving/climate conditions for instance periods of high acceleration or high engine load immediately after a cold start in cold climates there…
The sun visors may experience a high resistance short at the sun visor vanity lamp wiring after a service repair to the sun visor headliner or while gaining access above the headliner. This may…
On model series 463 with a 6 cylinder diesel engine the engine wiring harness may make contact with one of the brackets in the engine compartment and chafe by vibration during driving. Depending on…
The ESP hydraulic/control unit may have been damaged during shipping. This may affect operation of the ESP and/or the electronic parking brake.
On affected vehicles the eyelet connection of the parking brake secondary cable could break. If this happens the parking brake function can be affected
In the event of emergency braking or during an ESP regulation phase (e.g. avoiding manoeuvre) the hydraulic block may not prevent the locking of a wheel which could affect control of the vehicle.
Due to a manufacturing issue the front wheel bearing can become noisy and vibrate. If the driver does not take notice of these warnings then the bearing could fail and cause loss of control…
In the event of emergency braking or during an ESP regulation phase (e.g. avoiding manoeuvre) the hydraulic block may not prevent the locking of a wheel which could affect control of the vehicle.
There may not be adequate welding on one of the rear axle side arm bush housings. Therefore it is possible for the twist beam to become detached from the vehicle.
A possible non-conformity in the fitting of the tyre valves as well as an incorrect tightening torque of the valve securing nut could cause a valve to fail and a rapid loss of pressure…
A vacuum supply line for the brake booster may not have been fitted correctly. The vacuum supply line could become loose resulting in reduced braking assistance. The brakes will still work but the driver…
The driver' s airbag clockspring may ingest dust. This may cause the airbag warning light to illuminate. It may also affect the air bag operation in the event of a collision.
The bowden cable connected to the gear selector may come loose. This may prevent Park being engaged or disengaged.
The fuel supply tank from the fuel tank may leak into the engine bay area. The driver is likely to notice a lack of power and a smell of fuel.
The electronic shift lever on about 210000 of the above vehicles may allow a roll away condition if the vehicle�s engine is left running the parking brake is not engaged and the transmission is…
The bonnet may not close correctly over time because a possible non-conformity with the fixing of the bonnet catch. The driver may notice in certain cases difficulty in opening or closing the bonnet easily…
The bonnet may not close correctly over time because a possible non-conformity with the fixing of the bonnet catch. The driver may notice in certain cases difficulty in opening or closing the bonnet easily…
Under certain conditions the electrical terminal of the wiring harness connected to the Electronic Control Unit (ECU) of the EPS slide causes abrasion on the tin-plating layer of the connector. This can cause wear…