All UK Cars, vans & lorries recalls and safety alerts, newest first, with the hazard, affected models and what to do next. 4,358 listed.
It has been identified that the fuel delivery line/pipe may not have been installed to the correct specification. This could result in the incorrect tolerance between the fuel line/pipe and the vehicle under shield…
Certain driver side airbags the inflator might release shrapnel from the inflator container during deployment which could injure the driver.
The front suspension wishbones fixing bolts may not be to the correct specification which could lead to a risk of them breaking. This may affetc the driver's ability to control the vehicle.
The passenger air bag inflator may have been incorrectly manufactured/assembled. This may allow leakage of compressed gas and partial inflation of the airbag without a deployment command.
It has been identified that the airbag/SRS central sensor has been programmed with faulty software. If the vehicle is involved in a frontal or rearward collision then the airbag and seat belt tensioners may…
The material of certain front stub axle carriers may not be to specification and under extreme load conditions could crack. In the event of total failure a wheel could separate from the coach affecting…
It has been identified that the rear brake shoe lining material may not have been manufactured to the correct specification. This could result in a reduction in brake performance from the rear brakes.
The seatbelt mountings on the two seater bench seats may not be correctly tightened. This could cause the seatbelts not fully restrain the passengers and heighten the risk of injury if the vehicle is…
It has been identified that the Exhaust Gas Recirculation (EGR) valve pipe may fail/break. This will allow hot exhaust gases to escape and potentially damage component in the surrounding area.
The subject vehicles are equipped with a foot-operated parking brake system containing a parking brake cable and a crank lever which upon activation transmit the force of the parking brake pedal to the brake…
Moisture could enter the micro switches in the seat control unit and lead to intermittent shorting such that the power adjustable driver�s seat may intermittently not operate or may move forwards rearwards up down…
If has been identified that a certain batch of tyres may be affected by progressive damage which may cause the tyre tread to detach and adversely affect the control of the vehicle. The separated…
The heated washer jets may have jet heating elements which are not correctly sealed. There is a possibility that poor sealing could lead to corrosion due to water ingress and subsequent overheating of the…
The rear bench seat frame may impede the wiring harness connecting the fuel supply pump. This could affect fuel supply and the engine may cut out.
The bonding of the pressure sensors on the axle modulator and proportional relay valve brake components may be incorrect and work loose. Leakage may occur in the area of the pressure sensor and applied…
It has been identified that the airbag/SRS central sensor has been programmed with faulty software. If the vehicle is involved in a frontal or rearward collision then the airbag and seat belt tensioners may…
It has been identified on certain Mokka models produced between 2013 & 2017 equipped with a rear bicycle carrier that if the rear bicycle carrier is not folded back into its correct stowed position…
The customer may experience vibrations or noise from the steering wheel due to cracks starting in the steering wheel hub. If not rectified in the worst case over time the steering wheel could break…
A bolt retaining the rear lower control arm to rear knuckle joint fixing may not have been tightened to correct specification. Failure of the bolt could affect control of the vehicle.
It has been identified that there is the possibility of a risk of an internal electrical short circuit in some cab interior lamps. In the worst situation this could result in a vehicle fire.
The bolts that hold the front seats to the floor may not be correctly tightened. This may cause the seat to become insecure and control of the vehicle to be compromised. Prior to failure…
It has been identified that during production the EGR pipe has been manufactured from incorrect thickness material. Due to the affect of stresses i.e. heat vibration etc on the pipe it can lead to…
The driver's air bag inflator may rupture during deployment. Metal shards may pass through the air bag material and cause injury to occupants.
It has been identified there is a possibility the front seatbelt buckle stud may not have been punched correctly during production. This may result in a separation between the buckle and seatbelt bracket if…