Audi A4 recall: Front backrest may not perform correctly
The back-rests of the front seats may not have been assembled correctly. This may increase risk of injury to occupants during a collision.
All UK Cars, vans & lorries recalls and safety alerts, newest first, with the hazard, affected models and what to do next. 4,358 listed.
The back-rests of the front seats may not have been assembled correctly. This may increase risk of injury to occupants during a collision.
Two out of the four screws/bolts of the trailer hitch may not have been tightened correctly resulting in excessive stress to the other bolts. It is therefore possible that over time the connection could…
The high fuel pressure that builds up in the injection system when the engine is running can cause cracking and ultimately press the relevant fuel collection pipe off the injectors. This can cause a…
The multi-circuit protection valve section of the Air Processing Unit (APU) has been incorrectly piped. The consequence is that the driver could release the park brake without sufficient pressure in the service brake circuits…
It is possible that some suspension and brake components were not tightened correctly when building the car. It is possible for the components to become insecure and develop increase in noise from the suspension…
Vehicles equipped with stop/start system might have a starter motor failure while driving due to thermal damage of the starter cable.
It has been identified that due to a programing issue with the On-Board Supply Control Unit it is possible that the failure of one of the vehicle lights (dipped beam/main beam/daytime running light/rear fog…
It has been identified that the front side airbags may have been fitted with the incorrect detonators. If the vehicle is involved in a collision then the airbags may not operate as intended.
The maintenance flap under the driver's window may open unintentionally.
It has been identified that due to the incorrect programming of the Brake Control Module there is a possibility that the parking brake may not be set automatically when the Brake Hold or Hill…
Vehicles equipped with stop/start system might have a starter motor failure while driving due to thermal damage of the starter cable.
It has been identified by the manufacturer that the air-bag initiator does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none deployment of the air-bag.…
The igniter for the certain airbag modules may not have been correctly manufactured which may affect air bag deployment in the event of a collision.
It has been identified that in the subject vehicles there is a possibility the container of the inflator of the driver�s side may rupture. Toyota has not been able to establish the cause of…
It has been identified that the mating surface of the vehicle body for the panoramic glass roof panel may have been contaminated during the primer phase of the instigation process. There is a possibility…
It has been identified by the manufacturer that the air-bag initiator does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none deployment of the air-bag.…
It has been identified that clamp bolt of the front lower control arm to knuckle fixing may have been incorrectly torqued/tighten this can cause a premature fatigue failure and possible separation of the joint.…
Vehicles included in safety recall R/2016/302 (P075) have received a modification which has subsequently been determined as not durable for the life of the vehicle. The engine harness may chafe on an engine bracket…
It has been identified by the seat belt Pre-Tensioner manufacturer that the pre-tensioner initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead…
It has been identified by the air-bag manufacturer that the air-bag initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none…
It has been identified by the air-bag manufacturer that the air-bag initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to non-deployment…
It has been identified that the bolt that connects the ground cable from the wiring harness of the Digital Motor Electronics (DME) to the engine block may not have been tightened/torqued to the correct…
It has been identified by the seat belt Pre-Tensioner manufacturer that the pre-tensioner initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead…
The passenger air bag may not meet the correct specification. In the possible event of a frontal collision front passenger airbag might not deploy as intended.