Citroen Jumpy, C5, Berlingo recall: Airbag may incorrectly deploy
On affected vehicles the driver's air bag inflation device may not conform to specification. As a result may not deploy correctly during an impact.
Every new product, food, vehicle, medicine and pet recall in the UK, newest first. Checked against official sources every 15 minutes. 10,672 listed.
On affected vehicles the driver's air bag inflation device may not conform to specification. As a result may not deploy correctly during an impact.
Fuel may leak from connections for the fuel tank breather and vent hoses on to the ground. Poor engine running may be experienced accompanied by the engine management warning light. The fuel on the…
Due to a deviation in the manufacturing process the retaining bolt for the right rear seal belt may not have been tightened to the correct specification. In the event of a collision the belt…
There is a possibility that a strut top mounting bearing could be damaged when a high load is applied to the strut such as when the vehicle is driven over a large bump. If…
The brake master cylinder push rod and boot are allowing air to pass into the master cylinder which will gradually extend the movement of the lever until the efficiency of the brake is compromised.
The fuel injectors supply rail could develop a leak over a period of time leading to a drop in fuel pressure which can affect the operation of the stop start system. In some extreme…
The fuel injectors supply rail could develop a leak over a period of time leading to a drop in fuel pressure in the injector supply rail which can affect the operation of the stop…
Due to a misrouted fuel pipe a metal hose clip my chafe against a nylon fuel pipe and may cause a fuel leak
The thread on the swivel pin of the track rod end might not be to specification. Therefore when the nut was tightened onto the thread the correct clamping force may not have been attained.…
The clutch release bearing may not be to specification which can result in difficult clutch and gear use. Additionally the oil pump pressure relief valve may not be to specification which can result in…
The airbag system Occupant Restraint Control (ORC) module may experience a front airbag and/or seatbelt pre-tensioner inadvertent deployment. An inadvertent deployment while driving could distract the driver and cause a crash without warning.
On affected vehicles the incorrect type of bolt may have been supplied during repair work involving the removal of the seat belt mount or belt reel.
The door child locks may disengage without driver knowledge. Though the door remains close it is possible for the door to then be opened from the inside.
The connection of the carbon drive shaft to the engine/transmission flange may not be to specification. Warnings of the development of the concern are: there will be noise malfunctions in the transmission and in…
The exhaust tailpipe variants K7D K7C and K7N can become loose. Variant K7D can fall away from the vehicle leading to a heightened risk of incident for other road users. Where an exhaust gas…
The Automatic Emergency Brake System (AEBS) may in certain traffic situations activate itself
A seat mounting may not conform to specifications. This may also impact on seat belt mountings and in the event of a collision the seat and/or belt may not act as intended.
There may be insufficient shielding between the engine exhaust and rearmost seat close-off panel which could lead to the seat close-off panel overheating and ultimately a fire hazard. Consumers should immediately stop using the…
The fuel hose from the tank mounted fuel pump may leak. With the most adverse circumstances a fire could occur.
In the event of an ignition misfire unburned fuel can be routed into the exhaust system. Ignition misfire could cause elevated exhaust temperatures that may pose a fire hazard.
Water may penetrate into the Electronic Brake Control Module (EBCM) connector. In the worst case water can enter the EBCM where a short circuit may lead to a risk of fire. Warning before the…
The lower nut & bolt securing the front shock absorber to the steering knuckle on either side of the affected vehicles may not have been tightened to specification. The bolt may work loose causing…
Due to a nonconformity of production the driver's air bag may not deploy correctly and may not provide protection as intended.
An incorrectly manufactured crank position sensor may cause the engine to unexpectedly cut out or not to start.