Land Rover Discovery recall: Airbag may deploy incorrectly
Due to a nonconformity of production the driver's air bag may not deploy correctly and may not provide protection as intended.
Every new product, food, vehicle, medicine and pet recall in the UK, newest first. Checked against official sources every 15 minutes. 10,352 listed.
Due to a nonconformity of production the driver's air bag may not deploy correctly and may not provide protection as intended.
An incorrectly manufactured crank position sensor may cause the engine to unexpectedly cut out or not to start.
On retrofit Low Entry Cab the steering limiter valve does not offload the system pressure correctly. This may cause high stress/forces on the link rod adjusting sleeve and ball joint which could lead to…
The engine may be difficult to start and / or the engine may stall without warning from fuel starvation and will be impossible to restart. When fuel is present in the fuel pump it…
Vehicles fitted with Adaptive LED Headlamps could experience a condition where the loss of a control signal in combination with a software error may cause the headlamps to switch off. There is a risk…
The power supply lines for the cab electrical system may not be fastened correctly at the electrical connecting point mounted on the cab firewall and as a result may be loose. A loose cable…
The rear calipers may not have been manufacturer to design specifications. as a result the seals may allow brake fluid to leak. This may affect brake efficiency but the brake fluid level warning light…
An abnormal noise may occur at the steering gear box when moving the steering wheel to right or left due to pinion plug nut loosening. If the concern is not resolved the pinion could…
Caduceus Pharma Ltd., Pemetrexed 25mg/ml Concentrate for solution for Infusion: caution in use after particulates identified in a small number of vials (EL (16)A/09)
A lock nut on a rear suspension tie rod may not have been manufactured to the correct specification. It may not act as intended even tightened to specification. It is unlikely the rod will…
The locking forces of the maintenance flap may not be to specification. At high speed and in combination with strong gusts of wind the plastic maintenance flap may detach from the vehicle and may…
The wheel bolts may not have been tightened correctly at the factory. If the bolts come loose the directional control of the machine may be compromised.
Action within 48 hours: B&S Healthcare are recalling two batches of parallel imported Medikinet XL 20mg modified-release capsules that have been incorrectly repackaged in 30mg cartons. (EL (16)A/08)
The drag link may not have been manufactured to the correct specification. There may be clearance between the draglink nut and the draglink arm which could potentially result in loss of steering control.
The software for the RSC is not to the correct specification and is unable to detect and mitigate a potential vehicle roll over condition. All other Stability Control Systems including Dynamic Stability Control (DSC)…
The front bevel box fitted to the engine assembly has not been manufactured to specification. The deficiency can lead to oil starvation to the input gear shaft could result in 6th gear input becoming…
The vibrations that occur during normal running of the motorcycle can turn the ignition off. If this occurs all power from the engine will be lost possibly putting the rider in danger.
The subject vehicle could unexpectedly lose drive and coast to a halt with no motive power due to a software issue in the powertrain control unit. In certain circumstances it is possible that the…
Due to an error in the size of the slots on rear wheel rim hub it is possible that the rear wheel rim might have been installed in the wrong way with the 4…
In extreme and hard driving conditions it is possible for the rear tie rod fixing bolt to become loose which can ultimately result in loss of vehicle control.
The left front brake caliper housing may have been cast from an incorrect material. Under extreme brake application the left front brake caliper housing may rupture and affect braking efficiency.
A clutch component might fail and cause the rear wheel to lock during motorcycle use. The likely cause is high and repeated stresses on the clutch assembly after a heavy use of the motorcycle…
The tow bar and whatever is being towed may become detached from the vehicle because a number of mounting points are missing from the tow bar. A loose trailer without directional control and possibly…
Under certain circumstances a dimensional error on the subject aftermarket front brake levers may cause the brake lever blade to contact the handlebar grip before maximum brake performance is achieved. This condition if present…