Car, van, motorbike and caravan safety recalls from the DVSA. 4,885 listed.
It has been identified that due to the incorrect programming of the Brake Control Module there is a possibility that the parking brake may not be set automatically when the Brake Hold or Hill…
Vehicles equipped with stop/start system might have a starter motor failure while driving due to thermal damage of the starter cable.
It has been identified by the manufacturer that the air-bag initiator does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none deployment of the air-bag.…
The igniter for the certain airbag modules may not have been correctly manufactured which may affect air bag deployment in the event of a collision.
It has been identified that in the subject vehicles there is a possibility the container of the inflator of the driver�s side may rupture. Toyota has not been able to establish the cause of…
It has been identified that the mating surface of the vehicle body for the panoramic glass roof panel may have been contaminated during the primer phase of the instigation process. There is a possibility…
It has been identified by the manufacturer that the air-bag initiator does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none deployment of the air-bag.…
It has been identified that clamp bolt of the front lower control arm to knuckle fixing may have been incorrectly torqued/tighten this can cause a premature fatigue failure and possible separation of the joint.…
Vehicles included in safety recall R/2016/302 (P075) have received a modification which has subsequently been determined as not durable for the life of the vehicle. The engine harness may chafe on an engine bracket…
It has been identified by the seat belt Pre-Tensioner manufacturer that the pre-tensioner initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead…
It has been identified by the air-bag manufacturer that the air-bag initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none…
It has been identified by the air-bag manufacturer that the air-bag initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to non-deployment…
It has been identified that the bolt that connects the ground cable from the wiring harness of the Digital Motor Electronics (DME) to the engine block may not have been tightened/torqued to the correct…
It has been identified by the seat belt Pre-Tensioner manufacturer that the pre-tensioner initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead…
The air box intake snorkel that may come in contact with the fuel rail or fuel line during operation. The resulting contact between the snorkel and fuel rail or fuel line may cause a…
The passenger air bag may not meet the correct specification. In the possible event of a frontal collision front passenger airbag might not deploy as intended.
It has been identified that due to the non-conforming layout of the airbag wiring and missing cut-proof protection the airbag wiring may interfere with the steering wheel wiring terminal. This can cause the abrasion…
The front impact sensor wire(s) may become detached during a crash event before the �impact signal� is recorded by the Occupant Restraint Controller (ORC). This may affect deployment of airbags and/or operation of pretensioners.
Affected vehicles may experience a lack of braking control on the rear axle when reverse gear is engaged.
The electrical contact of the Electronic Control Unit (ECU) of the Electric Power Steering (EPS) is not sufficiently robust over the service life of the vehicle. As a result the power steering support may…
It has been identified that due to an internal defect within the drivers air-bag if the SRS system detects an impact/collision which requires deployment of the air-bags then the drivers air-bag may not deploy.…
It has been identified that an error in the gearbox software can result in the incorrect message being displayed on the machine's instrument cluster. The gearbox position maybe displayed as being in the P…
It has been identified that due to a manufacturing issue the Anti-lock Braking System (ABS) Actuator Control Unit may have contamination within it. When in use the contamination particle can migrate within the ABS…
The insulation material of wiring for the stator may be damaged by engine heat and a short-circuit between the wiring may occur. Continued use of the motorcycle with this condition may cause the generating…