Every new product, food, vehicle, medicine and pet recall in the UK, newest first. Checked against official sources every 15 minutes. 10,752 listed.
On affected vehicles the steering rack and pinion assembly may have been manufactured with an incorrect amount of grease. In some circumstances this situation may result in steering lock. The manufacturer advises not to…
The insulation material of wiring for the stator may be damaged by engine heat and a short-circuit between the wiring may occur. Continued use of the motorcycle with this condition may cause the generating…
Insufficient clearance between the fuel rail and the engine can result in abrasion of the fuel rail posing a potential fuel leak. A fuel leak in the presence of an ignition source may pose…
Contact may occur between the wiring harness and the ABS modulator. An electrical connection may be created via the brake line between the ABS modulator and the vehicle ground. For this to occur the…
On certain 6 and 8 cylinder engine vehicles a faulty rear engine compartment panel/bulkhead may have been installed. It is therefore possible that the panel/bulkhead may contact the left exhaust catalytic converter due to…
It has been identified that the rear seatbelt extender may not retract as intended due to an issue with the individual friction conditions experienced by the belt extender which have not be programmed into…
It has been identified on the CLA Shooting Brake models with load compartment package the rear seat back-rest retaining bracket threaded connection may not have been manufactured to the correct specification. If the vehicle…
Medreich has provided handling instructions following several complaints that the child-resistant caps are difficult to open (EL(16)A/17)
It has been identified that the bonding on the glass panel of the rear left upper maintenance flap may not be to specification. This may allow the glass to vibrate and can result in…
One of the rear axle bolts retaining the stub axle carrier on the left and/or right side may not have been correctly tightened.This could allow the stub axle to separate from it's mounting.
The rear axle bolts may not have been correctly tightened which may generate a noise from inside the wheel arch or cause friction on the Tyre. If the concern is not addressed it is…
Seatcovers have been supplied which may affect deployment of the combined side/curtain airbags.
It has been identified that due to corrosion the engine hatch switches may become stuck in closed or compressed position. This will indicate that the hatch is closed regardless of whether the hatch is…
Some vehicles may have an incorrectly assembled front seat belt with the right hand seat belt fitted on the left hand side or vice versa. This could cause the seat belt upper anchorage to…
The rear seat buckle nuts may not be fully secure. In this condition the seat belt buckle may make a rattle noise. In an extreme case the nut may come off and the rear…
It has been identified that the incorrect mounting bracket for the power assisted steering pump may have been installed. This can cause misalignment of the pump and cause wear to the drive mechanism. This…
It has been identified that the durability of the lower trailing arm cannot be guaranteed. The arm can start to crack or fracture which if used on race track use or similar events can…
It has been identified that the striker wire on the bonnet lining may not have sufficient support to prove it with the security for its intended purpose. This can lead to incorrect locking of…
The Soft Ware applied during manufacture was incorrect for Medium Duty Engines. All heat temperature sensors are affected and are not functioning. The Heat Sensor function is lost and there is no warning to…
It has been identified that the driver can inadvertently circumvent the correct operating procedure for the closing/opening of the rear plug and slide door. If the door operating sequence has been overridden then when…
Due to exposure of water and dirt intrusion in the engine compartment the alternators may fail prematurely due to seized bearings. In the worst case the alternators could overheat causing an engine compartment fire.
It has been identified that certain internal body joints or fixing may not have been torqued to the correct specification. If not torqued to the correct specification then the joints/fixings may loosen over time.…
It has been identified that the locking nut of the differential pinion may not have been tightened to the correct specification. This will be identified to the driver by noise generated from the differential…
It has been identified that the bonnet striker support may corrode. If this corrosion is not treated there is a possibility the bonnet striker support may fail which will allow the bonnet to open…