Car, van, motorbike and caravan safety recalls from the DVSA. 4,885 listed.
Due to a non conformity during production the passenger's front air bag inflator may rupture during deployment. This may cause metal fragments to pass through the air bag and into the vehicle interior at…
In the event the heater fan resistor thermal fuse is affected by a combination of several factors there is a possible risk of fire.
The wheel hub units fitted with FAG bearings may exhibit premature wear in certain trailer applications. Prolonged use in these applications may result in degradation of the bearing grease. Early indicators may include noise…
A none conformity in the production process could result in a crack in female metal fitting around the circumference midway between locating pips. This could result in the failure of fitting resulting in separation…
On affected vehicles the near side front side air bag may have been incorrectly fitted in its module. As a result it may not deploy as intended during a collision increasing the risk of…
The fuel pressure sensor may not have correctly tightened during assembly. Over time this may affect the seal and allow fuel odour to escape. This could ignite in the presence of an ignition source.
The two horizontal fixing bolts that fix the ball hitch support bar to the tow bar frame may be incorrectly located. This defect can be seen by looking under the rear of the vehicle…
The fuel tubes are not earthed correctly. If an electro static discharge occurs on the fuel tubes it may cause a pin size hole in the fuel tube and a subsequent fuel leak. If…
1) The kick starter may not be correctly secure and slip during use. 2) A bolt may have dropped into the air cleaner during assembly. If a bolt is in the air cleaner assembly…
One or both bolts retaining the passenger air bag may have been omitted during production. As a result the airbag may not deploy as intended during a frontal collision.
The vehicles are equipped with 3-point lap-shoulder belt assemblies in all-three rear seating positions. The inner belt (buckle portion) of each of the rear three seat belt assemblies is secured to the floor of…
On some TRISTOP� actuators the chambers may not have been correctly assembled and the load from power spring and pressure is not fully taken. Under certain circumstances the parking side and the service sides…
There is a risk the passenger airbag mounting bolts are incorrectly installed which can lead to the airbag not correctly deploying. If a heavy front end collision occurs the passenger could sustain additional injury.
Abnormal deployment pressure may lead to rupture of the driver's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment.
The connecting rod may fail in early life under certain load conditions. The machines in question are designed to be used off road and as such power request is a factor in the control…
The connecting rod may fail in early life under certain load conditions. The machines in question are designed to be used off road and as such power request is a factor in the control…
The turbocharger oil pipe ferrule material may have cracked during its forming process. In this condition there is a risk that the oil pipe may lose its sealing resulting in the leakage of oil…
The mounting screws of the belt guide brackets at both the left hand and right hand C-Pillars may not have been tightened correctly. Therefore the seat belt/s may not perform as intended increasing the…
On 'B' Class models fitted with 'Easy Vario' rear seat option a bolt securing the seat bench to the body may have been omitted during production. This may allow the seat bench to lift…
On certain vehicles fitted with 9 speed transmission the back up battery may not connect during main battery failure. This may prevent selection of Park on the transmission or operation of the electronic parking…
The stitch spaces on the front seat back trims may be incorrect and tearing strength of the trim can be higher than normal. In the event of a collision it is possible that the…
On certain vehicles the Restraints Control Module may have been incorrectly connected. As a result the driver's seat belt pretensioner may not deploy
The spacer clips on the flexible fuel lines in the engine compartment may become displaced or fall out.This could cause he fuel lines to chafe against each other and become damaged.
Incorrect fuel pump seals were provided to all markets as Aftersales (AS) service parts for the Subject Vehicles. There is a possibility that some of them were used for the replacement and/or repair. In…