Vauxhall Vivaro and Movano recall: Loss of braking performance
The servo vacuum pump may fail causing a hard bake pedal loss of engine power and the vehicle may adopt limp home mode. A warning lamp may also illuminate.
Car, van, motorbike and caravan safety recalls from the DVSA. 4,885 listed.
The servo vacuum pump may fail causing a hard bake pedal loss of engine power and the vehicle may adopt limp home mode. A warning lamp may also illuminate.
On vehicles fitted with the four cylinder (OM651) engine the high pressure fuel lines may not have been manufactured to specifications. These lines may crack and allow fuel to leak. If an ignition source…
The fuel pre-filter heating may fail because of damage caused by scorching on the relay and its electrical connection. In extreme cases a fire could be possible.
The regulator/rectifier circuit board may have absorbed moisture during storage under high humidity conditions which reduced the strength of the adhesive used to fix the circuit board to the outer casing. Due to the…
It is possible for contamination to get between the tappet and the cam and cause surface damage and wear to the cam. If this condition occurs the valve clearance can become large and cause…
The adhesive used to fix the circuit board to the outer casing of the regulator/rectifier may have been affected by moisture. Due to the insufficient adhesion the heat generated can cause the circuit board…
Due to water ingress the tailgate power module may develop a short circuit. This may cause the module to fail and in extreme cases
Water ingress may gather in the spare wheel well may accumulate and cause the battery to short circuit.In extreme cases this could cause a fire.
The retaining bolts securing the front seat belts to the 'B' Pillar may not have been tightened to the correct specification. They may work loose and the seat belt could detach.
The glue used to fix the high top to the base vehicle overtime loses adherence. This may not be evident to the driver and water may cause none visible corrosion and could affect interior…
The fuel tank breather may have been positioned incorrectly during assembly and become kinked. If the hose is kinked the air flow through the breather hose will be obstructed and the fuel tank internal…
The earth attachment for the on board power supply control unit may not be to specification. This can lead to various electrical events. In the most unfavourable case the engine may start when using…
The right hand side parking brake cable may interfere with the fuel tank. As a result there is possibility of peeling off the coating on the fuel tank. In the worst case the fuel…
During manufacture of the rear brake hose the crimping not to specification which can lead to the connection failing when the brake is applied and loss of brake effort at the rear brake.
Two concerns. 1. If corrosive liquids enters the ignition switch it can cause the terminals inside to corrode. This can result in either the engine still running after the key has been taken out…
It has been identified that under certain situations it is possible for the weld joining the bracket post to the base plate to fail. This could allow the TV monitor to become detached from…
In some circumstances the driver and passenger may experience consequent switching off of the instrument panel light and possible deactivation of other electronic systems such as the ABS and airbags. The concern is caused…
A windscreen installer may not have followed due processes when replacing windscreens. These windscreens may allow water ingress cause excessive wind noise and may also detach in the event of an accident.
Due to a nonconformity of the sealing agent fuel may seep from the tank sender unit. Fuel could be ignited if it come into contact with an ignition source.
The high pressure fuel lines have not been manufactured to the correct specification which over time can lead to crack formation and fuel leaking. Fuel escaping in the presence of an ignition source could…
Due to an overlap in manufacturing tolerance the throttle body butterfly may not return when the throttle pedal is released. As a result engine speed may not fall as expected.
Fuel gauge may not show correct level
The headlamp filament may snap as incorrect material has been used in the filament. Should the aforementioned happen the headlamp will stop working and in the worst case scenario the filament can short circuit…
The Rear Stabiliser bar may not be to specification. This could result in the Rear Stabiliser bar cracking and failing which will result in the vehicle handling characteristics being adversely affected.