Jeep Wrangler recall: Airbag circuit may be compromised
The driver' s airbag clockspring may ingest dust. This may cause the airbag warning light to illuminate. It may also affect the air bag operation in the event of a collision.
Car, van, motorbike and caravan safety recalls from the DVSA. 4,885 listed.
The driver' s airbag clockspring may ingest dust. This may cause the airbag warning light to illuminate. It may also affect the air bag operation in the event of a collision.
The bowden cable connected to the gear selector may come loose. This may prevent Park being engaged or disengaged.
The fuel supply tank from the fuel tank may leak into the engine bay area. The driver is likely to notice a lack of power and a smell of fuel.
The electronic shift lever on about 210000 of the above vehicles may allow a roll away condition if the vehicle�s engine is left running the parking brake is not engaged and the transmission is…
The bonnet may not close correctly over time because a possible non-conformity with the fixing of the bonnet catch. The driver may notice in certain cases difficulty in opening or closing the bonnet easily…
The bonnet may not close correctly over time because a possible non-conformity with the fixing of the bonnet catch. The driver may notice in certain cases difficulty in opening or closing the bonnet easily…
Under certain conditions the electrical terminal of the wiring harness connected to the Electronic Control Unit (ECU) of the EPS slide causes abrasion on the tin-plating layer of the connector. This can cause wear…
The bolts securing the rear axle support should not be re-used after removal. Affected vehicles may have had the rear axle support refitted after repair work using the original fitted bolts. These may work…
A potential chafing condition has been identified between the alternator power cables and P-clamp. If chaffing occurs it may result in a short circuit. This could lead to initially some flickering of certain Malfunction…
Affected vehicles may suffer surface corrosion that could cause the secondary bonnet latch to remain in the open position when the bonnet is closed. Under these circumstances if the bonnet has not been properly…
Frame may break/deform near the bottom of the down tube under the front of the seat. This will lead to the handle bars getting closer to the driver and the body lowering towards the…
Carbonised grease may accumulate between the contact points in the ignition switch reducing the insulation performance inside the switch. In this condition the switch may generate heat resulting in smoke and in the worst…
The ignition switch may unintentionally change position while driving. This may result in a loss of engine power power steering assist power brake assist or disable the airbag function.
An error in production of the brake master cylinder may cause a reduction in braking efficiency.
A potentially faulty weld between the plate carrier and the hub of a clutch could be faulty/cracked and could fail. This can cause limp-home mode to be adopted or all drive to be lost.…
The Cargo-Box retaining bracket may become loose and dislodge.This may allow the exhaust to overheat a seat panel and may lead to fire. THE MANUFACTURER ADVISES NOT TO USE THE MACHINE.
In the event of a significant frontal collision the driver's airbag may not deploy correectly due to a non-conformity which occurred in the supplier's production process. The airbag when deployed may cause injury to…
The seat may not remain in position when subjected to greater than normal driving forces such as those involved in an impact. This may possibly cause injury to the driver/passenger seated in the right…
On Audi Q7 vehicles with 7 seats manufactured within a specific period the indentations on the cross piece of the third row of seats were not made correctly. As a result the third row…
The vehicles are equipped with a fuel evaporative emission control unit (canister) assembled to the fuel tank. There is a possibility that a crack could develop on the resin channel for the emission gas…
The front panel of the panoramic sunroof may not have been bonded correctly which can lead to rattling noises during a journey. If the loosening front panel is not detected this poses a potential…
Due to an error in production cracks may form in the steering wheel. This could compromise the strength of the steering wheel and in extreme conditions may detach.
Due to an incorrect tightening operation in the production plant the locking function of the hood might not work correctly. This may allow the bonnet to open whilst the vehicle is in motion
On affected vehicles the curtain side air bag inflator may have a crack in a weld. If this crack propagates gas may leak and in certain conditions partially in inflate the air bag.