Vehicle recallVehicle · 20 Jun 2017
Where the car incurs severe engine damage resulting in the engine failing to turn over (engine seizure) and if the driver repeatedly attempts to start the engine despite the engine not cranking the very…
Vehicle recallVehicle · 20 Jun 2017
The left and right widow airbags may not meet specification. As a result they may not deploy in the event of an accident.
Vehicle recallVehicle · 20 Jun 2017
The left widow airbag may not meet specification. As a result it may not deploy in the event of an accident.
Vehicle recallVehicle · 20 Jun 2017
The right widow airbag may not meet specification. As a result it may not deploy in the event of an accident.
Vehicle recallVehicle · 20 Jun 2017
The propellant mixing ratio in the igniters of the front passenger airbag assembly may not meet specification. If the airbag is required and activated it might not deploy or not completely deploy. This could…
Vehicle recallVehicle · 20 Jun 2017
The connection fitting of the vacuum line to the brake booster is not to specification and my not be durable. If the connection fails the brake booster will no longer be supplied with vacuum.…
Vehicle recallVehicle · 20 Jun 2017
On vehicles with ABS/ESC the earth connection may be interrupted. This may cause failure of the ABS/ESC system
Vehicle recallVehicle · 20 Jun 2017
On vehicles with ABS/ESC the earth connection may be interrupted. This may cause failure of the ABS/ESC system.
Vehicle recallVehicle · 20 Jun 2017
The ball head connecting the brake pedal and the master brake cylinder the ball head might not be locked properly into the ball cage. If the driver accidentally pulls up the brake pedal the…
Vehicle recallVehicle · 19 Jun 2017
The tightness of one of the air conditioning compressor support mountings may not be correct to specification. This will result in an abnormal noise and possibility of the compressor becoming insecure
Vehicle recallVehicle · 19 Jun 2017
The tightness of one of the air conditioning compressor support mountings may not be correct to specification. This will result in an abnormal noise and possibility of the compressor becoming insecure
Vehicle recallVehicle · 16 Jun 2017
Insufficient tightening of the steering column coupling could lead to wear of the steering coupling during use. In case of excessive wear of the steering coupling the coupling eventually may not transfer the effort…
Vehicle recallVehicle · 15 Jun 2017
The pre-tensioner in the driver�s side third row passenger seat belt may not have been produced according to the correct specification In the event of a collision the pre tensioner and seat belt will…
Vehicle recallVehicle · 14 Jun 2017
The software for the Electronic Stability Program (ESP) is faulty. The fault could lead to a low residual pressure in the hydraulic system so the brakes are applied and gain heat. This increased heat…
Vehicle recallVehicle · 13 Jun 2017
Under certain conditions the headlight control unit may reboot which can affect the headlight operation
Vehicle recallVehicle · 12 Jun 2017
The screw securing the steering wheel to the splines may be missing. This can lead to loss of directional control thereby increasing the risk of a collision.
Vehicle recallVehicle · 12 Jun 2017
The urea water injector mounting flange on the exhaust front pipe may fail and allow the urea water injector to separate from the front pipe. This situation could result in noncompliance with requirements prescribed…
Vehicle recallVehicle · 12 Jun 2017
Due to an in the fitting process replacement screens may not have been correctly fitted. Drivers may notice water ingress and/or wind noise
Vehicle recallVehicle · 12 Jun 2017
There is a possibility of interference and fretting between the ABS brake pipes and the secondary air system connection which over a period of time could in the most extreme cases lead to loss…
Vehicle recallVehicle · 9 Jun 2017
In unusual situations the Active Electronic Braking System (AEBS) can misinterpret freeze frame data and cause the brakes to fully apply when not required. The driver does have time to cancel the braking activity.…
Vehicle recallVehicle · 8 Jun 2017
3rd row seat retaining bolts and 2nd row seat belt shoulder anchor retaining bolts may not be tightened to the correct specification
Vehicle recallVehicle · 8 Jun 2017
Contacts inside the electric power steering motor may not have been correctly formed. Failure of these contacts would cause the loss of power steering assistance.If this happens a warning lamp will illuminate
Vehicle recallVehicle · 8 Jun 2017
Due to a firmware error the vehicle's restraint control module will not recognise the passenger seat is occupied. In the event of an accident the passenger airbag will not deploy
Vehicle recallVehicle · 8 Jun 2017
Due to an error in the manufacturing process the headlamp lens may not conform to specification.